Mr-Glass Custom & Geometric Windows Nationwide | Winslow Windows & Doors

Mr-Glass Custom & Geometric Windows in Palm Beach: What to Know First

Mr-Glass custom and geometric windows in Palm Beach need a technician who understands how shaped glass behaves under Florida sun, salt air, and hurricane code. We’re an independent Mr-Glass service provider, not a manufacturer affiliate, and we repair, replace, and install these windows throughout Palm Beach, typically completing most custom-shape jobs within five to ten business days once glass and framing are on hand. Straight answer on price: expect to budget $800-$3,200 per opening depending on the geometry, glass package, and whether the frame needs full replacement. This page is for homeowners with a Mr-Glass window that’s fogged, leaking, cracked, or never fit quite right in its opening. For a free estimate on any Mr-Glass custom or geometric window, call (561) 831-7863 and a live person picks up.

Call (561) 831-7863

How Mr-Glass Products Fail - and How We Fix Them

• Radius-corner stress cracks on Mr-Glass Signature Series picture windows. In Palm Beach, the combination of intense morning sun on east-facing elevations and air-conditioned interiors creates a sharp thermal differential across the glass. On Mr-Glass Signature Series units with tight radius corners, we see hairline cracks that start at the curve and run inward. This isn’t a manufacturing defect in most cases, it’s thermal stress from the Palm Beach climate. We replace the insulated glass unit with a heat-strengthened or tempered lite specified for the radius, then verify the setting block placement so the next thermal cycle doesn’t repeat the failure.
• Arched transom sag on Mr-Glass Architectural Series. Arched windows over doors and tall fixed transoms carry a lot of their own weight, especially on wide openings. After years of Palm Beach humidity cycling, the wood or composite jamb can compress slightly, and the arch begins to drop at the crown. You’ll notice the gap at the top of the arch widening, or the window binding when someone opens the door below it. We remove the unit, shim and reinforce the opening header, and reset the window with proper support clips rated for the weight. On Mr-Glass Architectural Series specifically, the original install often skipped the crown support clips, and that’s the root cause we correct.
• Seal failure between glass lites on Mr-Glass custom trapezoids and triangles. Odd-shaped glass isn’t cut the same way as rectangular stock, and the edge seal on a Mr-Glass trapezoid has more linear feet of sealant per square foot of glass than a standard rectangle. That means more opportunity for desiccant saturation and fogging. We commonly see this on Mr-Glass units installed in Palm Beach pool enclosures and sunrooms, where reflected UV off the water accelerates seal degradation. Our fix is full IGU replacement, not a drill-and-fill fog repair, because the latter leaves the failed sealant in place and voids most workmanship expectations on a piece this expensive.
• Frame corner joint separation on Mr-Glass aluminum geometric windows. On angular shapes like hexagons and pentagons, the corner keys take significant shear load, particularly during wind events. We’ve opened up Mr-Glass aluminum frames in Palm Beach where the corner joinery has cracked or pulled apart, letting water in at the miter. The window still looks fine from the street, but the interior drywall below tells the real story. We disassemble the frame corner, replace the corner key with a reinforced part, apply fresh sealant, and re-square the unit before reinstalling.
• Hardware binding on Mr-Glass radius-edged casement and awning operators. Curved frame profiles on Mr-Glass casements mean the operator arm travels along a non-linear path. Over time, with salt air corrosion from living near the Palm Beach shoreline, the hardware loses its factory lubrication and begins to bind. Owners report cranking harder and harder until the handle snaps off in their hand. We replace the operator assembly with a corrosion-resistant aftermarket part, not a cheap big-box replica, and re-align the hinge track so the window operates with one finger again.

Our Mr-Glass Custom & Geometric Windows Process

1. 1
   Call and describe what you’re seeing. A live person answers at (561) 831-7863, takes your address, and schedules a time that works. No voicemail trees, no call center. You’ll talk to someone who knows Mr-Glass products by name.
2. 2
   On-site diagnostic. A background-checked, uniformed technician measures the opening, checks the glass condition, inspects the frame and hardware, and identifies whether the issue is the IGU, the frame, the installation, or a combination. We carry a moisture meter and a straightedge on every custom-shape job because geometry hides problems a visual check alone misses.
3. 3
   Parts decision: OEM vs. quality aftermarket. We lay out the options honestly. Mr-Glass OEM glass and hardware preserve the original engineering, but lead times can stretch. Quality aftermarket parts, where appropriate, get the job done faster at a lower price without compromising the weather seal. We never install a part we wouldn’t put on a window at Ed’s own house.
4. 4
   The repair or replacement. For glass-only failures, we remove the failed IGU, prep the frame, and set the new lite with proper setting blocks, shims, and sealant. For frame or installation failures, we pull the entire unit, correct the opening, and reinstall so the window sits square and drains properly.
5. 5
   Test and verify. We run the window through its full range of motion, check for air and water infiltration at the perimeter, and confirm the glass sits without any stress points. If it’s an impact-rated unit, we verify the glass etch and ensure the seal matches the original spec.
6. 6
   Cleanup and the Done Right Promise. We haul off the old glass and frame, sweep up, and walk you through what we did. Every Mr-Glass job we complete is covered by our 36500-Day Done Right Promise: if it’s not done right, we make it right. Period.

What Mr-Glass Custom & Geometric Windows Costs in Palm Beach

Here are the numbers we quote most often on Mr-Glass work in Palm Beach, based on the geometry and the scope of the fix:

• Insulated glass unit replacement, single rectangular Mr-Glass window: $450-$900
• Insulated glass unit replacement, custom geometric shape (triangle, trapezoid, pentagon): $900-$2,200
• Arched or radius-top Mr-Glass window, full frame replacement: $1,800-$3,500
• Corner joint or frame repair on angular Mr-Glass unit: $350-$750
• Hardware replacement (operator, hinge, or lock) on Mr-Glass casement or awning: $150-$400

What moves the price: the number of glass lites, whether the shape requires a custom template, whether the frame is salvageable or compromised, and whether we’re dealing with impact-rated glass that carries its own fabrication costs. Some Palm Beach homes on the Intracoastal side also require stainless steel hardware upgrades to fight salt corrosion, which adds $75-$150 per window. We give written, line-item quotes before work starts, and the price we quote is the price you pay. No change orders, no surprise line items on the final invoice. Call (561) 831-7863 for a free estimate.

Why Palm Beach Homeowners Call Winslow Windows & Doors for Mr-Glass Work

Ed Winslow founded this company in 2011, and his name is on the door and on every job we do. We’re not a faceless installer with a ticket number; we’re the local crew that Palm Beach homeowners call when a Mr-Glass unit fails and they want it fixed by someone who actually understands the product. Our technicians work on Mr-Glass windows every month, and when a Mr-Glass part isn’t the right answer, we can compare it against what we know from installing PGT, CGI, CWS, and ES Windows, so you get an honest recommendation, not a sales pitch. Every call is answered by a live person, 24/7. Every tech is background-checked and in uniform. And every job, from a single sash repair to a full geometric window replacement, is covered by our 36500-Day Done Right Promise. My name’s on the truck. That’s reason enough to do it right.

FAQs